Toyota 4Runner FUEL FILTER STOP THE FUEL LEAK
when INSTALLING NEW FUEL FILTER
and filter RE-LOCATION KIT
2nd Gen Toyota
This kit we found online solves TWO PROBLEMS
A) Most filters are located on frame rail onthe back side of frame
( above/behind torsion bar) Very hard to reach with RR labor
time of up to 45 minutes !
B) Item 2 .... Toyota used a 14.5 MM inverted flare fitting . Fram and
other REPLACEMENT filters LEAK GAS on installation.
C) Go back to ITEM A ) Labor to RR this filter averages 45 minutes
By the time you INSTALL the new filter and DISCOVER it LEAKS GAS
you now have to REMOVE THE BRAND NEW FILTER !
D) Many Toyota WEBSITES ( user sites ) explain that the NEW FRAM
(and many other NON OEM Toyota filters LEAD MASSIVELY and
MANY SITES EXPLAIN that the mechanic RE-INSTALLS the OLD filter
and NO LEAK ... Installs the NEW FILTER and MASSIVE GAS LEAK
E ) Please note that each RR ( remove and replace TAKES 45 MINUTES )
The SOLUTION
Go to the dealer ship and purchase a near Fuel $ 50 Filter
or USE the Filter kit in this ad .
RE-LOCATING the FILTER is OPTIONAL.
WHY NOT replace 45 minutes with under 5 minutes by RE-LOCATING FILTER !
( Fram / Wix and most aftermarket are $ 12-$ 20 )
AND now the Toyota websites TELLS YOU TO INSTALL
PURE COPPER ( soft / annealed ) CRUSH WASHERS
on for each 14.5 mm IF fitting on the filter ;
The crush washers actually SEAL on the LIP of the inverted ( IF ) fittings
The CRUSH WASHER ACTUALLY HAS A
TOYOTA PN # of 90430-14002 and a cost of $ 2.81 each
( Actual size of CRUSH WASHER fits INSIDE each end of the filter )
FILTER RE-LOCATION ( OPTIONAL )
On my personal 4 Runner the fuel line was routed tight against the frame .
The HARD fuel lines that go to the filter position the filter in a very
difficult spot to replace . Average labor time is 45 minutes if YOU
do not have a gas leak . My mechanic worked in a dealership for
over 20 years ...and quoted me 45 minutes labor IF NEW FILTER
DID NOT LEAK . ( It did / so did 3 other brand new replacements ! )
He re-installed the OLD FILTER and NO LEAKS !
He went to his
computer and ordered me the TOYOTA FUEL FILTER kit
we now offer to you in this ad !
F) We have in this kit
1 ) fuel line cutter ( small to allow you to rotate cutter )2) 36\" of high quality fuel line with 4 clamps
3) Two Copper Crush Washers
a) Remove stock filter ( simply remove fittings ) b) Pull existing hard lines away from frame ( This gives you access to use cutter we supply in kit) c) Cut approx 1\" of hard line off w/fitting on end of each piece d) Do this to CREATE a short nipple to attach FLEX hose we supply e) INSIDE each fitting you will PLACE ONE Copper Crush washer f) Installation of Crush washers and tightening of fittings is now done on workbench g) PLACE the filter wherever you want in ALONG APPROX 2 feet of FRAME SECTION h) SIMPLY PLACE the new filter where you want it . My Toyota was about 12\" from where it was stock however 100% accessible . I) Simply use the fuel line in the kit and Cut the hard lines where you need to Each of my FLEX LINES is approx 12\" long ( you have 36\" in kit) J) I have helped friends replace filters after they re-locate and TOTAL TIME is now under 5 minutes start to finish . K) Everyone asks this ...YES spare COPPER CRUSH WASHERS are sold. Each kit comeswith a card to re-order 2/4/10/or 24 packs of Copper Crush Washers Froo | Froo Cross Sell, Free Cross Sell, Cross promote, Marketing, listing Apps, Apps, Application
4
77
(not us) Is now adding Internet sales tax to orders.
It is being done to all sales. (Not just ours)
