Celica Forums General Discussion Exterior Pilar...

does anyone have a link to site that sells Celica Pilars that will alow me to put gagues in them?

here ya go...


www.egauges.com/vdo_acce.asp?Subgroup=Toyota_Celica&Cart= [egauges.com]

bro do those come like Fiberglassed to a pilar or is that just a pod that you have to ither Fiberglass in or screw in...


cuz i was orginaly gunna buy a 3 or 2 gauge pod and mold it into the stock pilar..not mine because i dont want to mess up i did this kind of stuff before but i want to mess up my stock ones just incase...
but no one is selling stock pilars...

so now i am trying to find one that is already molded it...

i got mine from www.thelostrican.com [thelostrican.com] but i think the site is down...

the link I posted has pillars which need to be put on top of the existing A-Pillar and fastened in place... check out my thread linked below - it has pics of the pillar


https://celicahobby.com/ubbthreads/thread.f_1870081001_0_collapsed_5__1.html

http://www.gaugepods.com/toyota.html

try them, they have the pillar that completely replaces the stock one for 3 gauges, they also have two and pne pods!!

THANKS GUYS FOR THE INFO!

that is gunna be my next mod...

but wtf what kind of gauges should i get , im gunna need 3 of them...

also can you post links of some sites that sell the gauges..

www.egauges.com [egauges.com] <--- where i got mine

2 1/16 100 PSI Elec. engine pressure gauge

2 1/16 140-260F Elec. engine temp gauge

2 1/16 8-18V Voltmeter - 12 volts


i guess ill get those...
but do i need to get anything else to install these?

do i get the machincal ones or the Eletric ones?

if your gonna get 3 gauges then go with the pillar from gaugepods.com!!

i just orderd the 3 gauge pilar
&
2 1/16 110F-265F / 40C-130C mechanical engine temp. gauge



2 1/16 100PSI/0-7 kp/cm2 mechanical engine pressure gauge




2 1/16 18-32 volt Voltmeter - 24 Volts Industrial

[quote]
2 1/16 18-32 volt Voltmeter - 24 Volts Industrial [quote]

My Celica peeks at 14v, I dont think that gauge will even register you have power cause its under the limits.

I have a 2k GTS Btw...

^ i guess i will have to install it to find out. lol if it dont then it dont no biggie but it will cool in there

Yeah I think if you car is even registering voltage on that meter there is a problem. the 8-18 is perfect for the Celica. But.. Mine is jsut tapped into the console power, maybe higer if you ran direct to battery.. Not sure.

Nope, it's still around 12 at the battery.

Is it just me or does this page only allow you to order 2 pod pillar attachments?

who did you finally go with??

be careful when your putting your piller back in , if you push to hard it will mess up the clip and it will kindda hang, it won't hang to bad , but it will not look like it did. I speek from experiance.

i went with

(Industrial Chrome)


From www.egauges.com [egauges.com]

and
www.gaugepods.com [gaugepods.com] for my 3 tripple pod

Im really happy with my C2's Going to get the Oil Pressure/temp next. Might pull my Driver Vents for them since I have the A-Piller already... Or.. Anyone have ideas for mounting spot? other then A-Pillar?

^ your drives side AC VENT on the left

how expensive you wanna go with teh gauges?
get
Volt
oil temp
water temp

^ i already got the gauges.

2 1/16 110F-265F / 40C-130C mechanical engine temp. gauge



2 1/16 100PSI/0-7 kp/cm2 mechanical engine pressure gauge




2 1/16 18-32 volt Voltmeter - 24 Volts Industrial

ok...engine temp? who makes teh cauges

yeah, they only have the 2-pod pillars... perfect for me though -

me too