|
Joined: Feb 2004
Posts: 198
Member 2000 Toyota Celica
|
Member
2000 Toyota Celica
Joined: Feb 2004
Posts: 198 |
how did you ppl get the buttom adapter that connects to the ecu tube in? i tryed forcing it in i was shaking the whole car. i couldnt get it in even with lube. also thier is a rattle every time i hit the throttle, wtf??
You Want the Bad Guy, Hear i Am.
|
|
|
|
Joined: Aug 2003
Posts: 128
Member 2002 Toyota Celica
|
Member
2002 Toyota Celica
Joined: Aug 2003
Posts: 128 |
You shouldn't even have needed to mess with the ecu tube for the aem cai???????
As for the shaking noise...here are some possibilities: 1.You didn't tighten everything as you should have...especially the connector flange on the fender well.
2. You didn't position the Intake tubing far enough away from the fender or fender plastic...thus the rattling sound.
3.You didn't cut a big enough hole in the fender well plastic for the Intake to have a little room to move. The whole engine moves slightly when you use the gas...so this is going to move the Intake as well, thus, check the size of the hole and make it a little larger.(Use a razor blade cause it cuts it like butta).
First check to make sure everything is tight...then, if the problem still pursists...cut the plastic better and reposition the Intake...in that order. My aem cai Intake has been on for over a year and I haven't had any noises or problems. Good luck bro.
02 GT-S R.I.P. 00 S2000
|
|
|
|
Joined: Feb 2004
Posts: 198
Member 2000 Toyota Celica
|
Member
2000 Toyota Celica
Joined: Feb 2004
Posts: 198 |
yes you do, you have to replace the ecu tube with an actual rubber tube connected with adapters. except the adpter on the radiator is so fuckn hard to snap in and its not like im a little bitch or anything either. it just would go man ![wtf wtf](https://celicahobby.com/forums/images/graemlins/celica/wtf.gif)
You Want the Bad Guy, Hear i Am.
|
|
|
|
Joined: Feb 2004
Posts: 27
Member 00 Toyota Celica GTS
|
Member
00 Toyota Celica GTS
Joined: Feb 2004
Posts: 27 |
I had the same problem, man. Dude i had to sand the adapter end a little to make it fit and even then it took me, my brother, and then my dad all of us alternating to finally pop it in! I don't know what's up with aem on that part when we measured the circumferenc the adapter was clearly larger than the hole it was suppose to go into! Goodluck!
|
|
|
|
Joined: Sep 2002
Posts: 3,028 Likes: 1
Bread Fishing.. 2001 Toyota Celica GT
|
Bread Fishing..
2001 Toyota Celica GT
Joined: Sep 2002
Posts: 3,028 Likes: 1 |
this guys install might help you out... Imported all the way from the UK click the guy below Good luck [ celica-club.co.uk]
LNK "you only need something when you know it exists..then it becomes a want"
|
|
|
|
Joined: Feb 2004
Posts: 1,716
Specialist 2000 Toyota Celica
|
Specialist
2000 Toyota Celica
Joined: Feb 2004
Posts: 1,716 |
^^^ ![lollol lollol](https://celicahobby.com/forums/images/graemlins/celica/lollol.gif) ...i saw that installed page..that dude look funny
|
|
|
|
Joined: Jan 2004
Posts: 5,125
Speed Omen 2002 Toyota Celica GT
|
Speed Omen
2002 Toyota Celica GT
Joined: Jan 2004
Posts: 5,125 |
yeah, the piece that goes in the radiator is tough to get in... use some type of lubricant and just keep trying. It took me like 30 minutes until it popped in
|
|
|
|
Joined: Oct 2003
Posts: 3,037
Specialist 2000 Toyota Celica
|
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037 |
i had the same problem with my INJEN Intake it took me about like one hour to get wat was going on wat i did was cut the top part and turn it over try to fit it in with the tube looking up if it goes in then do wat i did if not then i dont know
|
|
|
|
Joined: Feb 2004
Posts: 198
Member 2000 Toyota Celica
|
Member
2000 Toyota Celica
Joined: Feb 2004
Posts: 198 |
i cut the original ecu tube, filed it out, and stuck tit in there. worked great. still a tight fit but much easier to get in.
You Want the Bad Guy, Hear i Am.
|
|
|
|
Joined: Sep 2003
Posts: 3,070
Specialist 2000 Toyota Celica
|
Specialist
2000 Toyota Celica
Joined: Sep 2003
Posts: 3,070 |
Took me 5 mins to get it into the radiator. Just manage a little hammer down into there and give it a few taps. Don't even have to hit it that hard.
Aqua Teen Hunger Force...number one in the hood, G
|
|
|
|
Joined: Feb 2004
Posts: 198
Member 2000 Toyota Celica
|
Member
2000 Toyota Celica
Joined: Feb 2004
Posts: 198 |
You Want the Bad Guy, Hear i Am.
|
|
|
|
Joined: Sep 2003
Posts: 3,070
Specialist 2000 Toyota Celica
|
Specialist
2000 Toyota Celica
Joined: Sep 2003
Posts: 3,070 |
The piece that goes into the radiator.
Aqua Teen Hunger Force...number one in the hood, G
|
|
|
|
Joined: Sep 2002
Posts: 3,028 Likes: 1
Bread Fishing.. 2001 Toyota Celica GT
|
Bread Fishing..
2001 Toyota Celica GT
Joined: Sep 2002
Posts: 3,028 Likes: 1 |
darn i'm starting to worry how I'll install mine
LNK "you only need something when you know it exists..then it becomes a want"
|
|
|
|
Joined: Sep 2003
Posts: 3,070
Specialist 2000 Toyota Celica
|
Specialist
2000 Toyota Celica
Joined: Sep 2003
Posts: 3,070 |
It's easy, don't worry about it. Only the mechanically inclined will have a problem or two.
Aqua Teen Hunger Force...number one in the hood, G
|
|
|
|
Joined: Dec 2003
Posts: 781
Senior Member 2000 Toyota Celica
|
Senior Member
2000 Toyota Celica
Joined: Dec 2003
Posts: 781 |
what about dumb ass'es...like myself? ![smile smile](https://celicahobby.com/forums/images/graemlins/celica/smile.gif)
|
|
|
|
Joined: Feb 2004
Posts: 198
Member 2000 Toyota Celica
|
Member
2000 Toyota Celica
Joined: Feb 2004
Posts: 198 |
cut ecu tube insert the adapter into it, its easy, you will need to file it abit then force it in
You Want the Bad Guy, Hear i Am.
|
|
|
|
Joined: May 2004
Posts: 7
New Member 2000 Toyota Celica
|
New Member
2000 Toyota Celica
Joined: May 2004
Posts: 7 |
i think my aem cai was messed up during manufactoring, because the air sensor tube isnt where it is in that guys pics. U know that hole that you screw the sensor too, well that isnt down there near where the stock one was, instead its all the wy up at the top, right next to the throttle body! THe rubber grommet that holds the Intake to the engine will be pushed up against it, thats how foar up it is. Idk if this is some new design or if its messed up, ne info would be good. thnks
|
|
|
- Part Reviews
- OEM Parts Catalog
- Body Kits, Ground Effects
- Hoods, Hood Scoops
- Spoilers, Wings, Splitters
- Side Mirrors
- Head/Tail Lights & Bulbs
- Interior Appearance
- Interior Performance
- Engine Dress-up Kits
- Exhaust Systems
- Engine Performance
- Bars, Braces, Coilovers
- Shocks, Springs
- Wheels, Tires, Brakes
- Audio, Video, Security
|
|
|
|