Previous Thread
Next Thread
New Reply
Print Thread
Rate Thread
Page 1 of 2 1 2

Joined: Oct 2002
Posts: 505
Senior Member
2000 Toyota Celica GT
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505
I've been getting a lot of requests for the angel eyes install guide. So instead of PMing everyone, I will post it here so everyone can see. wink

Angel Eye Installation Instructions


Step1: Remove front bumper and remove headlights. Each headlight have 3 bolts. Use a 10mm socket wrench to remove.

(left headlight)
[Linked Image from imagestation.com]
[Linked Image from imagestation.com]

(right headlight) The right headlight is connected to the wiper fluid container. Just pull the tabs out and it should come right out.
[Linked Image from imagestation.com]
[Linked Image from imagestation.com]


Step2: On back side of headlight there are 3 copper screws, remove all 3. Remove all bulbs also. The low beam bulb has a rubber cap that needs to be removed.

[Linked Image from imagestation.com]
[Linked Image from imagestation.com]

Step3: Heat oven to 300 degrees and then Turn off, Place headlight on a big enough pan with a towel underneath and place in oven for 10-15 minutes. This process softens the glue around the headlight making it easier to take apart.

[Linked Image from imagestation.com]

Step4: Immediately begin to pry open the headlight by using a screw driver and a knife. You may have to repeat step3 several times because the glue hardens again.

[Linked Image from imagestation.com]

Step5: After headlight is apart, set aside bottom piece. The top clear piece has another plastic piece inside. There are 2 screws that need to be removed. Then work the plastic piece out. Do not use too much force because the plastic piece can easily break.

[Linked Image from imagestation.com]
[Linked Image from imagestation.com]

Step6: Next you need a tube of clear silicon adhesive. Take the angle eye and place adhesive on the black area of the angel eye on the rough side. Then place the angel eye around the circle area of the plastic piece and let dry.

[Linked Image from imagestation.com]
[Linked Image from imagestation.com]

Step7: After fully dry, make sure that the wire are through the circle. Next flip the plastic piece over, bend the wires and tape them to the reflector piece using electrical tape. This process keeps the wires from touching the projector lens.

[Linked Image from imagestation.com]
[Linked Image from imagestation.com]

Step8: Test angel eyes before putting everything back together.

[Linked Image from imagestation.com]

Step9: Put the plastic piece back inside the clear part and put both screws back. (See step5).

Step10: You are now ready to put both top and bottom pieces of the headlight back together. During this process, run wires through the opening of the low beam.

[Linked Image from imagestation.com]

Step11: You are now ready to reseal the headlight. One way of doing this is to place headlight in a vice. Make sure the headlight is in between towels to prevent scratches. Next, use a heat gun and slowly remelt the glue all the way around the headlight while applying pressure.

WARNING: Do not place headlight back in oven to remelt the glue. This will cause the angel eye to warp.

Step12: After headlight is resealed, put all bulbs back together. The angel eyes wires should be coming out of the low beam opening. Next, put the rubber cap back on with wires coming out.

[Linked Image from imagestation.com]

Step13: You are now ready to put you headlight back in your car. The wires should be long enough to reach your parking lights for connections. If you would like to wire them to a switch, you would need to crimp an extension.

[Linked Image from imagestation.com]
[Linked Image from imagestation.com]

Angel Eyes after installation.

[Linked Image from imagestation.com]

[Linked Image from imagestation.com]
[Linked Image from imagestation.com]


GOOD LUCK!

Ken Carrion
(Karrion28)

Joined: Feb 2003
Posts: 523
Senior Member
2000 Toyota Celica
Senior Member
2000 Toyota Celica
Joined: Feb 2003
Posts: 523
pimpalisous!!! thumbsup you stilll have headlights tho right?

Joined: Sep 2002
Posts: 767
Senior Member
2001 Toyota Celica GT
Senior Member
2001 Toyota Celica GT
Joined: Sep 2002
Posts: 767
those look great! thumbsup

Joined: Sep 2002
Posts: 398
Member
2002 Toyota Celica
Member
2002 Toyota Celica
Joined: Sep 2002
Posts: 398
very cool man i wanna do that

Joined: Jul 2002
Posts: 10,110
05 WRB
2005 Subaru WRX STi
05 WRB
2005 Subaru WRX STi
Joined: Jul 2002
Posts: 10,110
this should go into the Installs section and sticky it for a bit.


SUBARU TECNICA INTERNATIONAL

Joined: May 2002
Posts: 1,147
ECelica Staff
2000 Toyota Celica GT
ECelica Staff
2000 Toyota Celica GT
Joined: May 2002
Posts: 1,147
Originally Posted by TRDGTS014
this should go into the Installs section and sticky it for a bit.

Will do. But, will leave it here for a while. That is an excellent install guide. thumbsup Very detail, very nice.


[Linked Image]
Really BAD reality TV is the reason I stopped watching MTV.

Joined: Jan 2003
Posts: 2,154
ECelica Staff
2002 Toyota Celica GT
ECelica Staff
2002 Toyota Celica GT
Joined: Jan 2003
Posts: 2,154
that is cool! thumbsup great job Ken, hey dude, any updates on your plastics in the engine bay? i like to see the progress...


[Linked Image]

Joined: May 2003
Posts: 89
Member
2002 Toyota Celica GT
Member
2002 Toyota Celica GT
Joined: May 2003
Posts: 89
Karrion were did you buy the angel eyes lenses can they be purchased anywhere I would like to do this for my next mod on both my celica and my rsx.

Joined: Oct 2002
Posts: 505
Senior Member
2000 Toyota Celica GT
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505

Joined: May 2003
Posts: 89
Member
2002 Toyota Celica GT
Member
2002 Toyota Celica GT
Joined: May 2003
Posts: 89
Thats pretty cool how much did all this cost def doing this now. thanx for the info

Joined: May 2003
Posts: 89
Member
2002 Toyota Celica GT
Member
2002 Toyota Celica GT
Joined: May 2003
Posts: 89
'nother question Ken how bright r they can they light up the road well. In the pics they look dull (no knocking them honest)?

Joined: Oct 2002
Posts: 505
Senior Member
2000 Toyota Celica GT
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505
cost to make these is no more than $20. LED's can be pretty expensive for just little bulbs.

They are brighter in person. At night when the headlights are on, they are not noticeable at all. because the light of headlights is to bright and it drowns it out. The best time to have these on is at dusk. You could disable your day time running lights to have it more noticeable.


Joined: Jan 2003
Posts: 2,154
ECelica Staff
2002 Toyota Celica GT
ECelica Staff
2002 Toyota Celica GT
Joined: Jan 2003
Posts: 2,154
i read the link you posted about creating the Angel Eye, the clear acrlyic rod must me multipled scratched cut around on both sides?

[Linked Image from students.washington.edu]

and about the LEDs, if you combine them do you need only one resistor?


[Linked Image]

Joined: Oct 2002
Posts: 505
Senior Member
2000 Toyota Celica GT
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505
nope, only one side. While installing them make sure the smooth side faces out.

Yes the LEDs are combined so you only need one resistor per ring.

One more thing I forgot to add: The angel eyes should be 2.5 inches in diameter for a good fit. thumbsup

Joined: Jun 2003
Posts: 11
Member
Member
Joined: Jun 2003
Posts: 11
r those legal?

Joined: Oct 2002
Posts: 505
Senior Member
2000 Toyota Celica GT
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505
Originally Posted by latin_guy
r those legal?

The only color that is legal is white. thumbsup

Joined: Apr 2003
Posts: 297
Member
2003 Toyota Celica GT Turbo
Member
2003 Toyota Celica GT Turbo
Joined: Apr 2003
Posts: 297
Ding I'm hungry I thought your baking a cake!just kidding looks good!!! thumbsup


[Linked Image]

Joined: Jun 2003
Posts: 479
the dude
2002 Toyota Celica GT
the dude
2002 Toyota Celica GT
Joined: Jun 2003
Posts: 479
Those look sick. Nice job on making em yourself. thumbsup

Joined: May 2002
Posts: 29
Member
Member
Joined: May 2002
Posts: 29
what if you have to replace the bulb? you gotta open the whole thing up again? seems like a hassle.

Joined: Oct 2002
Posts: 505
Senior Member
2000 Toyota Celica GT
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505
Originally Posted by jpra923
what if you have to replace the bulb? you gotta open the whole thing up again? seems like a hassle.

LED's are specifically made to withstand a very very long life period. If one were to blow out then yes it would be a bit of a hassle to replace it.

Joined: Nov 2002
Posts: 163
Member
Member
Joined: Nov 2002
Posts: 163
I make these, any color, for $45 shipped. Please let me know if interested. Thanks. If you like you can email me at juliaronay@aol.com

Joined: Jun 2003
Posts: 16
Member
Member
Joined: Jun 2003
Posts: 16
Originally Posted by Karrion28
Originally Posted by jpra923
what if you have to replace the bulb? you gotta open the whole thing up again? seems like a hassle.

LED's are specifically made to withstand a very very long life period. If one were to blow out then yes it would be a bit of a hassle to replace it.

but well worth it

Joined: Jul 2003
Posts: 159
pizza bagel
2000 Toyota Celica GT
pizza bagel
2000 Toyota Celica GT
Joined: Jul 2003
Posts: 159
that is very sweet, i'll have to try that one day...


A boat's a boat but a mystery box could be anything! Even a boat!

Joined: Jul 2003
Posts: 46
IAD
Member
00 Toyota Celica
Member
00 Toyota Celica
Joined: Jul 2003
Posts: 46
I have a friend who currently makes IS300 kits on my site and he uses fiber optics for the actual angeleye. I am sure that you could do that here as well then you would not have to do all that BS cutting. The fiber optics cost more but depending on the demand you could probably charge more because you would have a better quality product.

Last edited by IAD; Jul 15, 2003 9:23pm.


Joined: Mar 2003
Posts: 73
Member
02 Acura RSX-S
Member
02 Acura RSX-S
Joined: Mar 2003
Posts: 73
u dont have to take the front bumper off...i put mine on w/ out taking it off. w/ no problem.

Joined: Mar 2003
Posts: 7
New Member
New Member
Joined: Mar 2003
Posts: 7
what size resistor do you use?

Joined: Oct 2002
Posts: 505
Senior Member
2000 Toyota Celica GT
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505
Originally Posted by scelicagt
what size resistor do you use?

I used 220 ohm resistors.

Joined: Sep 2003
Posts: 3
New Member
New Member
Joined: Sep 2003
Posts: 3
Those lights look awesome!!! One question though... aren't they illegal????

Joined: May 2002
Posts: 5,979
Likes: 9
ECelica Admin
2001 Toyota Celica GT
ECelica Admin
2001 Toyota Celica GT
Joined: May 2002
Posts: 5,979
Likes: 9
Originally Posted by Dancinchick
Those lights look awesome!!! One question though... aren't they illegal????

Blue and yellow headlights. Headlights must be white - blue and yellow are illegal (24011 VC).

Headlights brighter or higher wattage than those from the factory. You may be able to see better, but the lights are illegal (24011 VC).

from...
https://celicahobby.com/forums/ubbt...ording-to-california-highway-patrol.html

I dont see anything illegal about them thumbsup


[Linked Image]
It's not just your imagination...
Your day really does go by twice as fast while on EverythingCelica.com

Joined: Apr 2003
Posts: 71
Member
2001 Toyota Celica
Member
2001 Toyota Celica
Joined: Apr 2003
Posts: 71
Anyone have any ideas where to get the rod thing for the actual angel eye? confused I have looked at a bunch of places (Home Depot, Lowes, ACE, etc...) and cant find them.


[Linked Image]

Joined: Oct 2002
Posts: 505
Senior Member
2000 Toyota Celica GT
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505

I bought them from Wal Mart tongue

Joined: Apr 2003
Posts: 71
Member
2001 Toyota Celica
Member
2001 Toyota Celica
Joined: Apr 2003
Posts: 71
Uhh...any other ideas for places to go? I went to Wal-Mart and couldnt find them. confused


[Linked Image]

Joined: Sep 2003
Posts: 2
New Member
2003 Toyota Celica GT
New Member
2003 Toyota Celica GT
Joined: Sep 2003
Posts: 2
I found em at Home Depot...they are in the window blinds area...near the sinks and shit like that!

Joined: Oct 2003
Posts: 1,547
Likes: 1
Pizza Geek
2002 Toyota Celica GT
Pizza Geek
2002 Toyota Celica GT
Joined: Oct 2003
Posts: 1,547
Likes: 1
WOW that is SO simple its scary! eek

Joined: Nov 2003
Posts: 1
New Member
2000 Toyota Celica GTS
New Member
2000 Toyota Celica GTS
Joined: Nov 2003
Posts: 1
Hey hey hey!...to ask a stupid question...what will i need and where can i get these things to make these headlights?:)

Joined: Dec 2003
Posts: 1
New Member
2000 Toyota Celica
New Member
2000 Toyota Celica
Joined: Dec 2003
Posts: 1
looks good. where did you buy the angel eyes at.

Joined: Dec 2003
Posts: 4
New Member
2000 Toyota Celica
New Member
2000 Toyota Celica
Joined: Dec 2003
Posts: 4
this has to be one of the coolest mods you can do with a minimal amount of money grin
GREAT work thumbsup

Joined: Dec 2003
Posts: 4
New Member
2000 Toyota Celica
New Member
2000 Toyota Celica
Joined: Dec 2003
Posts: 4
Originally Posted by 00celicagts1589
looks good. where did you buy the angel eyes at.

Make them yourself! grin
Right here [students.washington.edu]

Joined: Jan 2004
Posts: 114
Member
2000 Toyota Celica GT
Member
2000 Toyota Celica GT
Joined: Jan 2004
Posts: 114
How did you get the LEDs inside the ring? I still can't even find the ring.

Joined: Oct 2002
Posts: 505
Senior Member
2000 Toyota Celica GT
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505
the rings were made with a clear curtain rod and the LED's were placed at the ends of the rings held by shrink tubing.

Joined: Jan 2004
Posts: 114
Member
2000 Toyota Celica GT
Member
2000 Toyota Celica GT
Joined: Jan 2004
Posts: 114
If anyone was wondering what size resistor to use like I was, I found the formula. It's R=(Vs-Vl)/I
R=resistance, Vs=voltage supply, Vl=voltage of LED, I=current of LED. thumbsup

Joined: Dec 2003
Posts: 1,781
Specialist
2000 Toyota Celica GT
Specialist
2000 Toyota Celica GT
Joined: Dec 2003
Posts: 1,781
you can get rods at home depot

Joined: Feb 2004
Posts: 1
New Member
2000 Toyota Celica GT
New Member
2000 Toyota Celica GT
Joined: Feb 2004
Posts: 1
So you made the angel eyes yourself? or did you buy the actual angel eyes? yours turn on with your headlights or with the daytime lights or what?

Joined: Apr 2004
Posts: 22
Member
2002 Toyota Celica GT
Member
2002 Toyota Celica GT
Joined: Apr 2004
Posts: 22
is there newher you can buy em at? i would really like to know, thanx

Joined: Jun 2004
Posts: 3
New Member
2000 Toyota Celica GT
New Member
2000 Toyota Celica GT
Joined: Jun 2004
Posts: 3
i would make the wires a little longer and attach then to your fog lights so you can turn them off and on also makes for good hiding tecnique (see successful speeding thread) LOL


hey! nice shoes! wanna race?
Kumasta! nice sabatos! wanna race?

Joined: Feb 2004
Posts: 93
Member
2001 Toyota Celica
Member
2001 Toyota Celica
Joined: Feb 2004
Posts: 93
It does seem like a lot of work, but if you just read the instructions PreatoRian gave very carefully you'll do it perfectly. I'd say there isnt a single place that would sell these to you, but if there is it'll be atleast 70 -100 dollars. I spent about 15 makin' mine and they turn heads whereever i am at night. Heres a pic:

[Linked Image from teamcelica.com]

Helps make the car look real agressive. (Sorry about picture size.)


[Linked Image]
2001 White Celica GT-S 4-Speed Tiptronic

Joined: Apr 2004
Posts: 123
Member
2000 Toyota Celica
Member
2000 Toyota Celica
Joined: Apr 2004
Posts: 123
yea, i got them to work. Figured out what my problem was. the first rods i tried to use were made of a different material. They melted bad and messed up the whole thing. The rods would bubble and yet still would not bend. Got some rods at Home Depot that worked great. I didn't have a dremel so they took me a really long time. I also made a few mistakes with the light being too big on the first one, so it took me 2 hours to make the first one. The second one only took 20 minutes tho. I used a butter knife in place of a dremel, came out great. Hope the install into the headlights is easy. hoping to do that tomorrow. Thanks for the help.

Joined: Feb 2004
Posts: 93
Member
2001 Toyota Celica
Member
2001 Toyota Celica
Joined: Feb 2004
Posts: 93
Nice, it all takes practice, especially with the wiring. It took me 7 LEDs before I got the wattage correct in my headlights. I hooked mine up so when you turn on the interior lights on(one turn of the head light knob), they come on and then the second turn is the headligths themselves which all worked out great because the angel eye headlights in blue are illegal to drive with. When my head lights were on so were the angels, but you couldnt see them because the head lights drown them out. Gotta love perfect conditions...


[Linked Image]
2001 White Celica GT-S 4-Speed Tiptronic

Joined: Jul 2004
Posts: 57
Member
2000 Toyota Celica GT
Member
2000 Toyota Celica GT
Joined: Jul 2004
Posts: 57
Great diy job! Just a question though. Ive gone to my local radio shack and the LED's there are $5 each and they're 1000 or 1100 mcd. On ebay i can get 20 of them @ 16,000mcd. Would using a brighter bulb make a huge difference? Im mostly concerned about the legal side of it.

Also for those that want to do this, ive found that shower curtain rings that are transparent are the perfect size, and there are some that are already knotched along the side. All you have to do is drill the holes for the LEDS.

Joined: Jul 2004
Posts: 57
Member
2000 Toyota Celica GT
Member
2000 Toyota Celica GT
Joined: Jul 2004
Posts: 57
i just finished this mod and 2.5 is a bit too small for a radius. Id go with a 3" to be safe, that way the bulb wont touch the projector.

Page 1 of 2 1 2
Join the conversation - Register Now or Log In to add your comment


Link Copied to Clipboard
Member Spotlight
Celica_Noob
Celica_Noob
2001 Toyota Celica GT
Arizona

Posts: 175
Joined: July 2004
Thank you.: My friends Tyler and John for install help
Random: Your next...
Show All Member Profiles 
Recent Topics
Can I change the shift knob in my Auto 1994 Celica?
by Kerfufflez - Nov 21, 2024 4:59am
2002 GT Power Window switch parts
by toolmd - Nov 15, 2024 1:44pm
Fuel Pump Refurbishment
by ColoCelica - Nov 2, 2024 8:27pm
Strange Problem with Gauge Cluster
by Paulseph - Nov 1, 2024 6:38am
Rebuilt Power Steering Pump for ZZT231
by AutoPartsBoxJPN - Oct 31, 2024 4:42pm
2001 Celica GT Damaged Clean Title- Parts or Project
by Jess818 - Oct 30, 2024 3:55pm
Battery cables for 1990 ST
by Dammy - Oct 29, 2024 10:36am
Customize Your Toyota Celica Privacy Policy · About · Contact
Privacy Policy · About · Contact
CelicaHobby.com is an independent Toyota Celica enthusiast website. CelicaHobby.com is not sponsored by or affiliated with Toyota Motor Sales, USA, Inc. in any way. The Toyota and Celica names and logos are trademarks owned by Toyota Motor Sales, USA, Inc.
© CelicaHobby.com, 2001-2024
Powered by UBB.threads™ PHP Forum Software 8.0.1
(Snapshot build 20240918)