|
Joined: Oct 2002
Posts: 505
Senior Member 2000 Toyota Celica GT
|
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505 |
I've been getting a lot of requests for the angel eyes install guide. So instead of PMing everyone, I will post it here so everyone can see. Angel Eye Installation InstructionsStep1: Remove front bumper and remove headlights. Each headlight have 3 bolts. Use a 10mm socket wrench to remove. (left headlight) (right headlight) The right headlight is connected to the wiper fluid container. Just pull the tabs out and it should come right out. Step2: On back side of headlight there are 3 copper screws, remove all 3. Remove all bulbs also. The low beam bulb has a rubber cap that needs to be removed. Step3: Heat oven to 300 degrees and then Turn off, Place headlight on a big enough pan with a towel underneath and place in oven for 10-15 minutes. This process softens the glue around the headlight making it easier to take apart. Step4: Immediately begin to pry open the headlight by using a screw driver and a knife. You may have to repeat step3 several times because the glue hardens again. Step5: After headlight is apart, set aside bottom piece. The top clear piece has another plastic piece inside. There are 2 screws that need to be removed. Then work the plastic piece out. Do not use too much force because the plastic piece can easily break. Step6: Next you need a tube of clear silicon adhesive. Take the angle eye and place adhesive on the black area of the angel eye on the rough side. Then place the angel eye around the circle area of the plastic piece and let dry. Step7: After fully dry, make sure that the wire are through the circle. Next flip the plastic piece over, bend the wires and tape them to the reflector piece using electrical tape. This process keeps the wires from touching the projector lens. Step8: Test angel eyes before putting everything back together. Step9: Put the plastic piece back inside the clear part and put both screws back. (See step5). Step10: You are now ready to put both top and bottom pieces of the headlight back together. During this process, run wires through the opening of the low beam. Step11: You are now ready to reseal the headlight. One way of doing this is to place headlight in a vice. Make sure the headlight is in between towels to prevent scratches. Next, use a heat gun and slowly remelt the glue all the way around the headlight while applying pressure. WARNING: Do not place headlight back in oven to remelt the glue. This will cause the angel eye to warp.Step12: After headlight is resealed, put all bulbs back together. The angel eyes wires should be coming out of the low beam opening. Next, put the rubber cap back on with wires coming out. Step13: You are now ready to put you headlight back in your car. The wires should be long enough to reach your parking lights for connections. If you would like to wire them to a switch, you would need to crimp an extension. Angel Eyes after installation. GOOD LUCK!Ken Carrion (Karrion28)
|
|
|
|
Joined: Feb 2003
Posts: 523
Senior Member 2000 Toyota Celica
|
Senior Member
2000 Toyota Celica
Joined: Feb 2003
Posts: 523 |
pimpalisous!!! you stilll have headlights tho right?
|
|
|
|
Joined: Sep 2002
Posts: 767
Senior Member 2001 Toyota Celica GT
|
Senior Member
2001 Toyota Celica GT
Joined: Sep 2002
Posts: 767 |
those look great!
|
|
|
|
Joined: Sep 2002
Posts: 398
Member 2002 Toyota Celica
|
Member
2002 Toyota Celica
Joined: Sep 2002
Posts: 398 |
very cool man i wanna do that
|
|
|
|
Joined: Jul 2002
Posts: 10,110
05 WRB 2005 Subaru WRX STi
|
05 WRB
2005 Subaru WRX STi
Joined: Jul 2002
Posts: 10,110 |
this should go into the Installs section and sticky it for a bit.
SUBARU TECNICA INTERNATIONAL
|
|
|
|
Joined: May 2002
Posts: 1,147
ECelica Staff 2000 Toyota Celica GT
|
ECelica Staff
2000 Toyota Celica GT
Joined: May 2002
Posts: 1,147 |
this should go into the Installs section and sticky it for a bit. Will do. But, will leave it here for a while. That is an excellent install guide. Very detail, very nice.
Really BAD reality TV is the reason I stopped watching MTV.
|
|
|
|
Joined: Jan 2003
Posts: 2,154
ECelica Staff 2002 Toyota Celica GT
|
ECelica Staff
2002 Toyota Celica GT
Joined: Jan 2003
Posts: 2,154 |
that is cool! great job Ken, hey dude, any updates on your plastics in the engine bay? i like to see the progress...
|
|
|
|
Joined: May 2003
Posts: 89
Member 2002 Toyota Celica GT
|
Member
2002 Toyota Celica GT
Joined: May 2003
Posts: 89 |
Karrion were did you buy the angel eyes lenses can they be purchased anywhere I would like to do this for my next mod on both my celica and my rsx.
|
|
|
|
Joined: Oct 2002
Posts: 505
Senior Member 2000 Toyota Celica GT
|
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505 |
|
|
|
|
Joined: May 2003
Posts: 89
Member 2002 Toyota Celica GT
|
Member
2002 Toyota Celica GT
Joined: May 2003
Posts: 89 |
Thats pretty cool how much did all this cost def doing this now. thanx for the info
|
|
|
|
Joined: May 2003
Posts: 89
Member 2002 Toyota Celica GT
|
Member
2002 Toyota Celica GT
Joined: May 2003
Posts: 89 |
'nother question Ken how bright r they can they light up the road well. In the pics they look dull (no knocking them honest)?
|
|
|
|
Joined: Oct 2002
Posts: 505
Senior Member 2000 Toyota Celica GT
|
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505 |
cost to make these is no more than $20. LED's can be pretty expensive for just little bulbs.
They are brighter in person. At night when the headlights are on, they are not noticeable at all. because the light of headlights is to bright and it drowns it out. The best time to have these on is at dusk. You could disable your day time running lights to have it more noticeable.
|
|
|
|
Joined: Jan 2003
Posts: 2,154
ECelica Staff 2002 Toyota Celica GT
|
ECelica Staff
2002 Toyota Celica GT
Joined: Jan 2003
Posts: 2,154 |
i read the link you posted about creating the Angel Eye, the clear acrlyic rod must me multipled scratched cut around on both sides? and about the LEDs, if you combine them do you need only one resistor?
|
|
|
|
Joined: Oct 2002
Posts: 505
Senior Member 2000 Toyota Celica GT
|
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505 |
nope, only one side. While installing them make sure the smooth side faces out. Yes the LEDs are combined so you only need one resistor per ring. One more thing I forgot to add: The angel eyes should be 2.5 inches in diameter for a good fit.
|
|
|
|
Joined: Jun 2003
Posts: 11
Member
|
Member
Joined: Jun 2003
Posts: 11 |
|
|
|
|
Joined: Oct 2002
Posts: 505
Senior Member 2000 Toyota Celica GT
|
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505 |
The only color that is legal is white.
|
|
|
|
Joined: Apr 2003
Posts: 297
Member 2003 Toyota Celica GT Turbo
|
Member
2003 Toyota Celica GT Turbo
Joined: Apr 2003
Posts: 297 |
Ding I'm hungry I thought your baking a cake!just kidding looks good!!!
|
|
|
|
Joined: Jun 2003
Posts: 479
the dude 2002 Toyota Celica GT
|
the dude
2002 Toyota Celica GT
Joined: Jun 2003
Posts: 479 |
Those look sick. Nice job on making em yourself.
|
|
|
|
Joined: May 2002
Posts: 29
Member
|
Member
Joined: May 2002
Posts: 29 |
what if you have to replace the bulb? you gotta open the whole thing up again? seems like a hassle.
|
|
|
|
Joined: Oct 2002
Posts: 505
Senior Member 2000 Toyota Celica GT
|
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505 |
what if you have to replace the bulb? you gotta open the whole thing up again? seems like a hassle. LED's are specifically made to withstand a very very long life period. If one were to blow out then yes it would be a bit of a hassle to replace it.
|
|
|
|
Joined: Nov 2002
Posts: 163
Member
|
Member
Joined: Nov 2002
Posts: 163 |
I make these, any color, for $45 shipped. Please let me know if interested. Thanks. If you like you can email me at juliaronay@aol.com
|
|
|
|
Joined: Jun 2003
Posts: 16
Member
|
Member
Joined: Jun 2003
Posts: 16 |
what if you have to replace the bulb? you gotta open the whole thing up again? seems like a hassle. LED's are specifically made to withstand a very very long life period. If one were to blow out then yes it would be a bit of a hassle to replace it. but well worth it
|
|
|
|
Joined: Jul 2003
Posts: 159
pizza bagel 2000 Toyota Celica GT
|
pizza bagel
2000 Toyota Celica GT
Joined: Jul 2003
Posts: 159 |
that is very sweet, i'll have to try that one day...
A boat's a boat but a mystery box could be anything! Even a boat!
|
|
|
|
Joined: Jul 2003
Posts: 46
Member 00 Toyota Celica
|
Member
00 Toyota Celica
Joined: Jul 2003
Posts: 46 |
I have a friend who currently makes IS300 kits on my site and he uses fiber optics for the actual angeleye. I am sure that you could do that here as well then you would not have to do all that BS cutting. The fiber optics cost more but depending on the demand you could probably charge more because you would have a better quality product.
Last edited by IAD; Jul 15, 2003 9:23pm.
|
|
|
|
Joined: Mar 2003
Posts: 73
Member 02 Acura RSX-S
|
Member
02 Acura RSX-S
Joined: Mar 2003
Posts: 73 |
u dont have to take the front bumper off...i put mine on w/ out taking it off. w/ no problem.
|
|
|
|
Joined: Mar 2003
Posts: 7
New Member
|
New Member
Joined: Mar 2003
Posts: 7 |
what size resistor do you use?
|
|
|
|
Joined: Oct 2002
Posts: 505
Senior Member 2000 Toyota Celica GT
|
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505 |
what size resistor do you use? I used 220 ohm resistors.
|
|
|
|
Joined: Sep 2003
Posts: 3
New Member
|
New Member
Joined: Sep 2003
Posts: 3 |
Those lights look awesome!!! One question though... aren't they illegal????
|
|
|
|
Joined: May 2002
Posts: 5,979 Likes: 9
ECelica Admin 2001 Toyota Celica GT
|
ECelica Admin
2001 Toyota Celica GT
Joined: May 2002
Posts: 5,979 Likes: 9 |
Those lights look awesome!!! One question though... aren't they illegal???? Blue and yellow headlights. Headlights must be white - blue and yellow are illegal (24011 VC). Headlights brighter or higher wattage than those from the factory. You may be able to see better, but the lights are illegal (24011 VC). from... https://celicahobby.com/forums/ubbt...ording-to-california-highway-patrol.htmlI dont see anything illegal about them
It's not just your imagination... Your day really does go by twice as fast while on EverythingCelica.com
|
|
|
|
Joined: Apr 2003
Posts: 71
Member 2001 Toyota Celica
|
Member
2001 Toyota Celica
Joined: Apr 2003
Posts: 71 |
Anyone have any ideas where to get the rod thing for the actual angel eye? I have looked at a bunch of places (Home Depot, Lowes, ACE, etc...) and cant find them.
|
|
|
|
Joined: Oct 2002
Posts: 505
Senior Member 2000 Toyota Celica GT
|
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505 |
I bought them from Wal Mart
|
|
|
|
Joined: Apr 2003
Posts: 71
Member 2001 Toyota Celica
|
Member
2001 Toyota Celica
Joined: Apr 2003
Posts: 71 |
Uhh...any other ideas for places to go? I went to Wal-Mart and couldnt find them.
|
|
|
|
Joined: Sep 2003
Posts: 2
New Member 2003 Toyota Celica GT
|
New Member
2003 Toyota Celica GT
Joined: Sep 2003
Posts: 2 |
I found em at Home Depot...they are in the window blinds area...near the sinks and shit like that!
|
|
|
|
Joined: Oct 2003
Posts: 1,547 Likes: 1
Pizza Geek 2002 Toyota Celica GT
|
Pizza Geek
2002 Toyota Celica GT
Joined: Oct 2003
Posts: 1,547 Likes: 1 |
WOW that is SO simple its scary!
|
|
|
|
Joined: Nov 2003
Posts: 1
New Member 2000 Toyota Celica GTS
|
New Member
2000 Toyota Celica GTS
Joined: Nov 2003
Posts: 1 |
Hey hey hey!...to ask a stupid question...what will i need and where can i get these things to make these headlights?:)
|
|
|
|
Joined: Dec 2003
Posts: 1
New Member 2000 Toyota Celica
|
New Member
2000 Toyota Celica
Joined: Dec 2003
Posts: 1 |
looks good. where did you buy the angel eyes at.
|
|
|
|
Joined: Dec 2003
Posts: 4
New Member 2000 Toyota Celica
|
New Member
2000 Toyota Celica
Joined: Dec 2003
Posts: 4 |
this has to be one of the coolest mods you can do with a minimal amount of money GREAT work
|
|
|
|
Joined: Dec 2003
Posts: 4
New Member 2000 Toyota Celica
|
New Member
2000 Toyota Celica
Joined: Dec 2003
Posts: 4 |
looks good. where did you buy the angel eyes at. Make them yourself! Right here [ students.washington.edu]
|
|
|
|
Joined: Jan 2004
Posts: 114
Member 2000 Toyota Celica GT
|
Member
2000 Toyota Celica GT
Joined: Jan 2004
Posts: 114 |
How did you get the LEDs inside the ring? I still can't even find the ring.
|
|
|
|
Joined: Oct 2002
Posts: 505
Senior Member 2000 Toyota Celica GT
|
Senior Member
2000 Toyota Celica GT
Joined: Oct 2002
Posts: 505 |
the rings were made with a clear curtain rod and the LED's were placed at the ends of the rings held by shrink tubing.
|
|
|
|
Joined: Jan 2004
Posts: 114
Member 2000 Toyota Celica GT
|
Member
2000 Toyota Celica GT
Joined: Jan 2004
Posts: 114 |
If anyone was wondering what size resistor to use like I was, I found the formula. It's R=(Vs-Vl)/I R=resistance, Vs=voltage supply, Vl=voltage of LED, I=current of LED.
|
|
|
|
Joined: Dec 2003
Posts: 1,781
Specialist 2000 Toyota Celica GT
|
Specialist
2000 Toyota Celica GT
Joined: Dec 2003
Posts: 1,781 |
you can get rods at home depot
|
|
|
|
Joined: Feb 2004
Posts: 1
New Member 2000 Toyota Celica GT
|
New Member
2000 Toyota Celica GT
Joined: Feb 2004
Posts: 1 |
So you made the angel eyes yourself? or did you buy the actual angel eyes? yours turn on with your headlights or with the daytime lights or what?
|
|
|
|
Joined: Apr 2004
Posts: 22
Member 2002 Toyota Celica GT
|
Member
2002 Toyota Celica GT
Joined: Apr 2004
Posts: 22 |
is there newher you can buy em at? i would really like to know, thanx
|
|
|
|
Joined: Jun 2004
Posts: 3
New Member 2000 Toyota Celica GT
|
New Member
2000 Toyota Celica GT
Joined: Jun 2004
Posts: 3 |
i would make the wires a little longer and attach then to your fog lights so you can turn them off and on also makes for good hiding tecnique (see successful speeding thread) LOL
hey! nice shoes! wanna race? Kumasta! nice sabatos! wanna race?
|
|
|
|
Joined: Feb 2004
Posts: 93
Member 2001 Toyota Celica
|
Member
2001 Toyota Celica
Joined: Feb 2004
Posts: 93 |
It does seem like a lot of work, but if you just read the instructions PreatoRian gave very carefully you'll do it perfectly. I'd say there isnt a single place that would sell these to you, but if there is it'll be atleast 70 -100 dollars. I spent about 15 makin' mine and they turn heads whereever i am at night. Heres a pic: Helps make the car look real agressive. (Sorry about picture size.)
2001 White Celica GT-S 4-Speed Tiptronic
|
|
|
|
Joined: Apr 2004
Posts: 123
Member 2000 Toyota Celica
|
Member
2000 Toyota Celica
Joined: Apr 2004
Posts: 123 |
yea, i got them to work. Figured out what my problem was. the first rods i tried to use were made of a different material. They melted bad and messed up the whole thing. The rods would bubble and yet still would not bend. Got some rods at Home Depot that worked great. I didn't have a dremel so they took me a really long time. I also made a few mistakes with the light being too big on the first one, so it took me 2 hours to make the first one. The second one only took 20 minutes tho. I used a butter knife in place of a dremel, came out great. Hope the install into the headlights is easy. hoping to do that tomorrow. Thanks for the help.
|
|
|
|
Joined: Feb 2004
Posts: 93
Member 2001 Toyota Celica
|
Member
2001 Toyota Celica
Joined: Feb 2004
Posts: 93 |
Nice, it all takes practice, especially with the wiring. It took me 7 LEDs before I got the wattage correct in my headlights. I hooked mine up so when you turn on the interior lights on(one turn of the head light knob), they come on and then the second turn is the headligths themselves which all worked out great because the angel eye headlights in blue are illegal to drive with. When my head lights were on so were the angels, but you couldnt see them because the head lights drown them out. Gotta love perfect conditions...
2001 White Celica GT-S 4-Speed Tiptronic
|
|
|
|
Joined: Jul 2004
Posts: 57
Member 2000 Toyota Celica GT
|
Member
2000 Toyota Celica GT
Joined: Jul 2004
Posts: 57 |
Great diy job! Just a question though. Ive gone to my local radio shack and the LED's there are $5 each and they're 1000 or 1100 mcd. On ebay i can get 20 of them @ 16,000mcd. Would using a brighter bulb make a huge difference? Im mostly concerned about the legal side of it.
Also for those that want to do this, ive found that shower curtain rings that are transparent are the perfect size, and there are some that are already knotched along the side. All you have to do is drill the holes for the LEDS.
|
|
|
|
Joined: Jul 2004
Posts: 57
Member 2000 Toyota Celica GT
|
Member
2000 Toyota Celica GT
Joined: Jul 2004
Posts: 57 |
i just finished this mod and 2.5 is a bit too small for a radius. Id go with a 3" to be safe, that way the bulb wont touch the projector.
|
|
|
Evan
2003 Toyota Celica GT
Washington
Joined: April 2003
Thank you.: To everyone on this board for the ideas! Random: Finally got RIMS!
|
Show All Member Profiles
|
|
- Part Reviews
- OEM Parts Catalog
- Body Kits, Ground Effects
- Hoods, Hood Scoops
- Spoilers, Wings, Splitters
- Side Mirrors
- Head/Tail Lights & Bulbs
- Interior Appearance
- Interior Performance
- Engine Dress-up Kits
- Exhaust Systems
- Engine Performance
- Bars, Braces, Coilovers
- Shocks, Springs
- Wheels, Tires, Brakes
- Audio, Video, Security
|
|
|
|